Recent Posts

Pages: 1 [2] 3 4 ... 10
11
4K,6K,8K Series / Re: SSL Computer ROMs (Recreating the Computer)
« Last post by mike_signo on November 10, 2026, 11:13:50 AM »
Thanks again Pascal, they have been very useful.
One of them looks like a bad read though: 683TR22F, the Total Recall EPROM (TMS2716, "Total Recall EPROM v 2.0f"). The file is 2 KB, but only the first 512 bytes and the last 512 bytes contain data. The whole middle 1 KB is FF. The code that is there calls routines that aren't in the file, and the Total Recall program on the SSL program disk also calls routines in the F600 to F7FF range that read as blank in this dump.
My guess is the read missed part of the chip, which would fit how awkward the TMS2716 is to read. It needs +12 V and -5 V, and A10 is on a different pin from a normal 2716.
The rest are fine and run in my emulator: P2970270 (VDU character ROM), P3010431 and P3010421 (RML COS 3.4), P3560404 (Ultimation 8051 firmware), plus the PROMs and JED files.
Does anyone have another read of 683TR22F,
12
4K,6K,8K Series / Re: SSL Computer ROMs (Recreating the Computer)
« Last post by mike_signo on November 10, 2026, 10:36:30 AM »
Hi Pascal,

Thanks a lot for the EPROM dumps, that’s really appreciated.
I'm happy to see that you're working on it as well. Your Arduino, CAN bus and touchscreen version looks amazing too. Nice to see that it's already interfacing with hardware.

It would be useful to stay in touch and compare notes on common issues as we go. I’ll be honest that, from past experience, collaborating on projects like this can be difficult, so I’m a bit careful about it. But I’m happy to share as much info as I can.

Best wishes to you and Steve.

Michele
13
4K,6K,8K Series / Re: SSL Computer ROMs (Recreating the Computer)
« Last post by pascal.verdet on November 10, 2026, 07:31:58 AM »
Hi Michele,

Great! We are also working on the same project with a colleague named Steve.
If we could exchange information, that would be a significant step forward.

A quick clarification: Most of the ROMs in the computer are those found on the NM4 boards and in the character generator for the VDU board...
The same applies to the "Total Recall" section...
One exception is the Ultimation interface board, which is built around an 8032 processor, with its program stored in ROM.

For my part, I have attempted to develop something similar using an Arduino's architecture, CAN Bus and a touchscreen.
I also thought that a "scribble strip display" would be a nice addition to the channel multiplexer board. (see the attached photos).

If we could pool our resources, that would be a very good thing. I am particularly curious about your "virtual machine."

With my best.
Pascal
14
4K,6K,8K Series / SSL Computer ROMs (Recreating the Computer)
« Last post by mike_signo on November 09, 2026, 09:41:05 PM »
Hi guys, hope you’re all well.

I’ve been reverse engineering the SSL computer, and I found that besides the floppy, you also need a lot of data stored in the ROM inside the computer. I have a working unit, but I don’t have an EEPROM reader. Does anyone have EEPROM bin files saved that they’d be willing to share? It would help a lot.

On the plus side, I’ve got the computer running in a virtual machine. There’s still plenty of work to do, mainly because Total Recall is a separate computer and I can’t get it working yet, but I’m confident we’ll get there.

Thanks,
Michele
15
4K,6K,8K Series / Re: Where to take the feed for DK Audio MSD100C
« Last post by jimlfixit on November 02, 2026, 03:41:00 PM »
Just seen this post (I am the wiring Moderator here and worked for SSL for 7 years)
Brief reply as I am busy with other stuff.
The 5 x stereo feeds appear on the patchbay, half normalled down to various 2 tracks but are ALL paralleled so if ONE is unbalanced, it will unbalance them ALL so be careful.
DL 32 is the connector involved of course but I haven't got time to look it up now to advise you but have the pinout here, although it changed a bit over the years after the 4 and 6K consoles.
Look at your patchbay (J/K and L/M to see what is there and message me if you have a problem.
Good luck and this should be an easy fix. Jim Lassen in the UK.
16
4K,6K,8K Series / Re: EOL for THAT Corp VCAs!
« Last post by gertius on October 21, 2026, 10:12:29 AM »
In an SSL 4k, what would the 2181 be needed for?
I know there is one 2151 in the 82e10 dynamics card, which could possibly be replaced with a 2181.
Which other places would need a 2151/2181?
17
4K,6K,8K Series / Bypass Film Pan card info needed
« Last post by C-Hawk on October 20, 2026, 05:45:25 AM »
Hi :)

I’m looking for some guidance on reverting an SSL 611 channel fitted with the Film Pan option back to the standard stereo configuration.

The Film Pan board on this channel is damaged, and I’d prefer to remove/bypass it rather than repair it.

From what I understand, removing the Film Pan board isn’t quite plug-and-play — the pan-pot wiring/routing needs to be restored to the standard 611 arrangement, and there may also be jumpers/links that need to be changed.

Does anyone have documentation, photos, or experience showing exactly what needs to be rerouted or linked when converting a Film Pan-equipped 611 back to stock stereo?

Any guidance would be hugely appreciated.

Thanks in advance,
Craig
18
4K,6K,8K Series / Re: EOL for THAT Corp VCAs!
« Last post by Matt Sartori on October 17, 2026, 05:44:48 PM »
Yes this is it.
bought as many as I could get my hands on and when that's gone I think we might need to start building our own..

The other thing is the RMS detector, not many of those available at all ...
19
4K,6K,8K Series / SSL faders
« Last post by Jdm5149 on October 17, 2026, 02:51:42 AM »
Starting new thread.  Last one was a bit long.  Working thru console and learning a lot.  Took apart and cleaned interior. 👍. Faders now are the current topic. Bar graph test shows different levels all placed at unity zero.  The ones that seem on point measure roughly 2.7kz when reading pins on fader tracks.  Others read 6-12.  I’ve seen where info shows the 2.7 are vca faders that SSl seemed to originally use and that the other faders can be calibrated to respond the same way.  Is this correct or should I be best to find replacements
20
4K,6K,8K Series / Re: Where to take the feed for DK Audio MSD100C
« Last post by Richealey on October 14, 2026, 02:10:40 AM »
It seems Dl 32 is your tape sends. Patch from a 2 track tape send patch point (top row).
Pages: 1 [2] 3 4 ... 10