Recent Posts

Pages: 1 2 [3] 4 5 ... 10
21
4K,6K,8K Series / Re: Where to take the feed for DK Audio MSD100C
« Last post by Protagonist on October 13, 2026, 07:21:36 PM »
Why not just use patch points? Wire it to a couple of TT connectors.
You could possibly use the 237 card. The 2 balanced output hybrids H1 and H2 feed a balanced output to connector conn2.
These are present but not used on my console.

Thanks for the reply mate.

Which patch points are you referring to out of interest?

Followed Conn 2 from H1/H2, on my console Conn 2 takes the 2 circuits to DL32, So I can add some pins and a couple of XLR's to my DL32 connector and pick up from there.
22
4K,6K,8K Series / Re: G+ Buss Compressor Calibration?
« Last post by Dave Dicson on October 13, 2026, 04:41:26 PM »
It is a little weird, but the 15 volts power for the 4 compressor cards comes from the compressor control card, regulated down from the 18 volts that is feed to the control card.
23
4K,6K,8K Series / Re: Console finally upright …..
« Last post by Jdm5149 on October 12, 2026, 06:17:11 PM »
Still learning  lol.  Working on faders and at unity some read perfect and some read low. Researching how to test with multimeter I notice some are 2.7 and others higher value. I guess mismatch of faders need to be brought into account.  Gonna try and keep separate buckets will each value
24
4K,6K,8K Series / Re: G+ Buss Compressor Calibration?
« Last post by ciaopatsy on October 12, 2026, 11:38:21 AM »
Thank you for the guidance!

Found some fried 10ohm power rail resistors, so it turned out there was more going on than I thought!

Replaced those and the compressor seems normal and slightly more controlled.

Great tip on the -10db pads, that worked awesome for keeping the compressor in check with a full mix going.
25
4K,6K,8K Series / Re: Console finally upright …..
« Last post by Jdm5149 on October 09, 2026, 02:15:05 PM »
Update. Totally took apart console and Deoxit and 99% all boards and connections. Pretty much looking brand new inside.  Beforehand I was chasing a issue with meters pegging with vca to meters engaged.  Putting everything back together I still had issue.  Turns out I started to inspect computer and found one pin on the analog output card indented.  Also a loose pc of solder that was shorting 2 pins.  I don’t know which of these 2 cleared the issue but it did.  👍👍
26
4K,6K,8K Series / Re: EOL for THAT Corp VCAs!
« Last post by tlmaen on October 04, 2026, 08:31:09 AM »
I bought the 2181b Version.
5,85.-€ if you buy 100+
The A-Version was more than 10.-€
With a distortion Meter you can trim the B version to better specs than the Pre-trimmed A Version,
and better than all of the 2150 Versions.
So I thought this would be a ok compromise…
27
4K,6K,8K Series / Re: EOL for THAT Corp VCAs!
« Last post by Protagonist on October 03, 2026, 10:32:44 PM »
I talked to Farnell yesterday, its no problem to order them. Shipping time is about two Months.
I ordered 100pcs.


the 2181? which version was it? 2181A?

Thanks

M
28
4K,6K,8K Series / Re: Console finally upright …..
« Last post by Jdm5149 on October 03, 2026, 09:03:32 PM »
here are some pics. the fader bus cards have a solid pc they are screwed into. the channels bus cards are a bit trickier maybe. thinking of leaving them in and clean them.  i see though if i start in each bucket on the right placing cards back in it might be easy to line both cards up. 
29
4K,6K,8K Series / Re: Console finally upright …..
« Last post by Jdm5149 on October 03, 2026, 01:58:27 PM »
Ok. Play time over now. Waiting all these years has me rushing things. Finally taking it apart and cleaning and testing all ribbon cables and connectors. Also probably gonna start recapping some of the center section cards.  I’ll post some pics but since this will be my board til ever I might as well get it right from the start 👍
30
4K,6K,8K Series / Re: How good is Ultimation?
« Last post by tlmaen on October 02, 2026, 08:54:42 PM »
So, I am going a bit forward with the Automation System.
I recently got myself a 3d Printer and made a special Fader Bracket for testing the Faders in the Console.

Because I have a very old Console, the Faders are very old big Metal Boxes.
Unfortunately they don't have the usual 100mm range and also have the Fader tip right in the middle of the Bracket.
Later Versions have the Cutout for the Fader off Center, wich allow to fit most modern replacements faders.
That's why I have to make a new Fader Bracket.

Does anyone know where SSL made their Fader Overlays for the 9k?
Is it Polycarbonate?
I am looking for a company who can make the for me (at a very good price, need more than 50pcs)

If someone have experience with it, please share your Info!

Tilmann
Pages: 1 2 [3] 4 5 ... 10