Recent Posts

Pages: 1 ... 8 9 [10]
91
Maybe the logic signals from the master section are not getting to the logic card on channels 1 & 2 from the bucket mother boards. Check the gold pins in the blue edge connectors on those mother boards. I have had issues with them in the past. Put a ribbon "bypass" jumper in to by pass the computer. If you replace the 50 way ribbon with a jumper under the faders, that total removes the computer and it's wiring.
92
@gollito said swapping in a different channel had same problem, so can't be a Logic card switch problem.

Has this just happened and it was OK before??
93
Check the DIP switches on the logic card (6082293) for those channels, that determine the Supercue behaviour.

Compare the positions to a working channel.

Anthony.
94
4K,6K,8K Series / SSL 4000 G+ — No Return on Channels 1–2 During Record Status
« Last post by gollito on August 26, 2026, 06:21:57 PM »
Hi to all friends ..

I’m troubleshooting a strange issue on my SSL 4000 G+. Channels 1–2 record normally and the input signal is present on the meters, but when the console is in Record Status, there is no DAW/tape return on channels 1–2. As soon as I stop recording and go to playback, the return on 1–2 works normally.

I have completely bypassed/cleared the patchbay and reset the relevant routing. I also tested the Pro Tools outputs directly: all output pairs (3–4, 5–6, 7–8, etc.) return correctly to the console, while 1–2 behave differently. However, the physical Pro Tools outputs 1–2 themselves are confirmed to be working, because when I use them during playback the console receives and reproduces the signal normally.

I also tested with Fader Reverse OFF, with exactly the same result. Most importantly, I swapped the channel strip from position 26 into position 1, and the problem remained at physical position 1. The original channel 26 works normally in its own position. So the fault does not appear to follow the channel strip.

At this point I’m wondering whether this could be related to the Record Status / tape-return switching circuitry associated with positions 1–2, rather than the channel modules themselves. My technician has suggested that a status circuit/status chip could potentially be involved. Has anyone experienced a similar fault on a G+ or has any insight into which circuitry I should investigate next?
95
SSLMIXED products / Re: SSL Virtual Tape Machine
« Last post by Dave Dicson on August 24, 2026, 04:12:15 PM »
We have a card version from Desk Doctor. It is not as "feature Rich" as your version. Nice job on your version.
96
4K,6K,8K Series / Re: Upper Bus Card problem
« Last post by Dave Dicson on August 21, 2026, 03:48:16 PM »
I should have said this in my above post. Swap the BICC connectors with channel 17 or 19 on the bus card from the patchbay. If problem goes away, there is your answer patchbay and wiring. If the problem is still there on channel 18, check the little gold contacts in the blue edge connector that haven't shorted or are not making contact with channel strip mother board. I have seen this in the past. Good luck.
97
4K,6K,8K Series / Re: Upper Bus Card problem
« Last post by Richealey on August 21, 2026, 02:09:58 PM »
Try swapping the BICC connector with another pair. Put 17/18 in 19/20 or 19/20 in 17/18 and see if the fault follows 18s wiring to the patchbay. I agree with Dave, it could be patchbay normalling. If you patch a signal using a TT into the lower Mic In patch point you should
bypass the normal connections. You could have something shorting the patch connector in the patchrow like a nut that fell off during shipping. Another test would be to pull the BICC connector for 17/18, use a patch cord in Mic In 18 and with an ohm meter measure between the hot, cold, and shield at the end of the patch cord. There should be no connection between them. Then check the patch point above the Mic In. This would check the normals. If you find a short you'll know what you're looking for. Hope this helps.

98
Hardware Development / Re: Computer scalability - Max channel count
« Last post by Dave Dicson on August 20, 2026, 05:26:48 PM »
We have 80 input SSL 4K and a 80 input SSL 9K + some smaller 4K's. I heard there is one studio that has a 96 input SSL 9J and a 120 input SSL 9J.
99
4K,6K,8K Series / Re: Upper Bus Card problem
« Last post by Dave Dicson on August 18, 2026, 08:21:52 PM »
Maybe check the patchbay mic input and normally jacks and it's wiring to and from patchbay for channel 18?
100
4K,6K,8K Series / Upper Bus Card problem
« Last post by tlmaen on August 18, 2026, 04:38:36 PM »
Hi,
CH 18 never worked properly since I bought the Console.
It always had trouble with the Mic level in REC Mode.
The Problem was sometimes there, sometimes not, and I suspected Sub-Cards in the Channel.
Now I narrowed it down to the upper Bus card (at least that's what I think atm...).

- The Level is about 18db lower than any other Channel, if you apply the same signal to the Micpreamp input (It stays low throughout the channel. Ins snd, Cues, Grp out).
- If you swap in another working Channel, the problem stays with Slot 18, not with the Channel Module.
- The upper Bus Card connector looks like it was replaced in the past. I checked all the solder joints on the backside, they look good.
- The Connector has pins 24, 54 fitted, wich shouldn't make any difference as these pins are not present at the 611E Edge connector (E-Series).
- I double checked all of the BICC Connectors if they are in the right place (if they were in the wrong place, it would affect two channels at the same time).

Now Idea why the problem is...
Hope someone can help!

Thanks,
Tilmann
Pages: 1 ... 8 9 [10]