Recent Posts

31

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 23, 2026, 03:56:57 PM »

I looked at manual and found jumper setting for multiplex cards but are there any for the logic cards ?  Are they used for working with computer or not. Or are they also used to determine channel location/number ?

32

4K,6K,8K Series / Where to take the feed for DK Audio MSD100C

« Last post by Protagonist on September 23, 2026, 01:32:38 PM »

Hi guys

Where is the best place to take a stereo signal from the 4000G to feed an external DK Audio MSD100C

Somewhere on the 237 meter distributor card?

Thanks

M

33

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 22, 2026, 08:09:33 PM »

K. Some progress. I booted up from my original 8” floppy drive that I repaired and I got all channels to light up in beginning of mix.  I don’t have a tape machine or pro tools running yet. Pressing execute brings me to the mix running screen but ofc no sympte running. The vca1-8 faders respond but all the channels are unresponsive. When I perform !tes for faders now
I see rows for 48 channels and still only vca 1-8 respond. All others pretty much wide open close to zero.

34

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 22, 2026, 04:47:57 PM »

i found multiplex settings in manual and set them up accordingly. i also ran the analogue in test for faders and only 1-16 and vca appeared.  1-16 were frozen open but vca 1-8 tested perfect. gonna swap analogue card and also make some spare 50 pin cables to test 

35

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 21, 2026, 05:19:21 PM »

Thanks.  I’ve been swapping channels around to test and get things to work. So I’m sure I gotta read the manuals at some point  lol.  Thanks again !

36

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Dave Dicson on September 21, 2026, 04:37:18 PM »

Yes, All the jumpers need to be switched, unless they have already been switched. The dip switches on the multiplex cards on all modules need to be set to different addresses. The address chart is in the manual.

37

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 21, 2026, 05:15:20 AM »

I’ve been troubleshooting and swapping channels around. Would all the multiplex cards need to be reset with their jumpers. I’m assuming so in order for total recall to work. Would that affect the automaton ??

38

4K,6K,8K Series / Re: Console finally upright …..

« Last post by horizonsound on September 20, 2026, 11:02:29 PM »

Have sent you an email.

39

4K,6K,8K Series / Re: Console finally upright …..

« Last post by Jdm5149 on September 20, 2026, 05:23:02 PM »

Been busy troubleshooting and have gotten very far. Board really looks and sounds great. Trying to figure this one out. In mix enabled with computer running only 1-16 and vca 1-8 light up for automation. After a bunch of options I then swapped 17-24 to slot 1-8 and 17-24 lite up on the console.  I already swapped out the computer card with another so it’s something other than the lights/switch’s card. Any suggestions.  Thanks !!

40

4K,6K,8K Series / Re: G+ Buss Compressor Calibration?

« Last post by Dave Dicson on September 18, 2026, 04:13:48 PM »

Newer versions have TO-220 voltage transistors. I have both types.